铝合金T型接头双侧激光焊接气孔缺陷影响规律研究

杨志斌; 李浩哲; 王斌; 陈禹昕

doi:10.3788/IRLA201847.0906004

铝合金T型接头双侧激光焊接气孔缺陷影响规律研究

doi: 10.3788/IRLA201847.0906004

1.
大连交通大学材料科学与工程学院,辽宁大连 116028

基金项目:

中国博士后科学基金（2017M611213）;辽宁省教育厅科学研究一般项目（JDL2016009）;先进焊接与连接国家重点实验室开放课题（AWJ-M16-05）

详细信息

作者简介:
杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn

中图分类号: TG456.7

Study on the influence rule of porosity defects for double-sided laser beam welding of aluminum alloy T-joint

1.
School of Materials Science and Engineering,Dalian Jiaotong University,Dalian 116028,China

摘要: 气孔缺陷是铝合金T型接头双侧激光焊接面临的主要问题，基于其工艺特点，文中系统研究了表面处理状态、光束入射角度、焊接速度、热输入和光束间距对气孔缺陷的影响规律。研究结果表明：铝合金表面保留一定厚度的纯铝包覆层才能最大程度地降低气孔缺陷；采用较大的光束入射角度和较高的焊接速度可以有效降低气孔缺陷，主要原因是小孔上方金属流动趋势由对流变为流向小孔内部更有利于气泡的逃逸；降低焊接热输入和增加光束间距均不利于降低气孔缺陷，造成小孔形状和贯通性改变并引起熔池流动行为的改变是其本质原因，保证双侧小孔对称和贯通才能利于气泡逸出并降低气孔缺陷。
- 双侧激光焊接 /
- T型接头 /
- 铝合金 /
- 气孔缺陷
Abstract: Porosity defect is the main problem for the double-sided laser beam welding of aluminum alloy T-joints. Based on its technology characteristics, the effects of the surface states, laser incident angles, welding speeds, heat inputs and laser distances on the porosity defects were studied in this work. The results indicate that the pure aluminium cladding layer is beneficial for reducing porosity defects. Using larger laser incident angle and welding speed are good for reducing porosity defects, the reason is that the fluid flow changes from convection to toward to keyhole, which can help pores escape from the weld pool. And, reducing heat input and increasing laser distance are bad for reducing porosity defects, the change of the keyhole shape and fluid flow are the essential reasons. It is necessary to ensure keyhole symmetry and pass-through, which can help the pores escape from the weld pool and reduce the number of the porosity defects.
- double-sided laser beam welding /
- T-joint /
- aluminum alloy /
- porosity defect

[1]	Siqueira R H M, Capella A, Riva R, et al. Comparing mechanical behavior of aluminum welds produced by Laser Beam Welding (LBW), Friction Stir Welding (FSW) and riveting for aeronautic structures[J]. Welding International, 2016, 19:1-7.
[2]	Peng Jin, Zhang Wenjie, Wang Xingxing, et al. Numerical simulation of effect of filler wire melting and filling mode on molten pool in laser welding[J]. Infrared and Laser Engineering, 2018, 47(3):0306005. (in Chinese)
[3]	Zhang Xinge, Li Liqun, Chen Yanbin, et al. Process and mechanical properties of laser-resistance hybrid welding for aluminum alloy T-joint[J]. Infrared and Laser Engineering, 2010, 39(1):138-142. (in Chinese)
[4]	Sun Z Q, Chen R, Wu A R. New materials and technology of Chinese civil aircraft[C]//Proc ICAMCS, 2016:926-930.
[5]	Janasekaran S, Jamaludin M F, Muhamad M R, et al. Autogenous double-sided T-joint welding on aluminum alloys using low power fiber laser[J]. International Journal of Advanced Manufacturing Technology, 2017, 90:3497-3505.
[6]	Oliveira A C, Siqueira R H M, Riva R, et al. One-sided laser beam welding of autogenous T-joints for 6013-T4 aliminium alloy[J]. Material and Design, 2015, 65:726-736.
[7]	Enz J, Khomenko V, Riekehr S, et al. Single-sided laser beam welding of a dissimilar AA2024-AA7050 T-joint[J]. Mater Des, 2015, 76:110-116.
[8]	Tao W, Yang Z B, Chen Y B, et al. Double-sided fiber laser beam welding process of T-joints for aluminum aircraft fuselage panels:Filler wire melting behavior, process stability, and their effects on porosity defects[J]. Opt Laser Technol, 2013, 52:1-9.
[9]	Qi Junfeng, Niu Zhen, Zhang Dongyun, et al. Control of shaping of welds for CO2 laser welding shipbuilding T-section aluminum alloy[J]. Chinese Journal of Lasers, 2008, 35(2):297-302. (in Chinese)
[10]	Ma Xuyi, Gong Shuili, Zhang Jiuxing, et al. Influence of the welding conditions on weld defects in double-sided laser beam welded T-joints of Ti-6Al-4V alloy[J]. Chinese Journal of Lasers, 2016, 43(2):0203006. (in Chinese)
[11]	Yang Z B, Tao W, Li L Q, et al. Numerical simulation of heat transfer and fluid flow during double-sided laser beam welding of T-joints for aluminum aircraft fuselage panels[J]. Opt Laser Technol, 2017, 91:120-129.
[12]	Chen Kai, Yang Wuxiong, Huang Rui, et al. Porosity control of 1420 Al-Li alloy by dual-beam laser welding[J]. Infrared and Laser Engineering, 2010, 39(1):133-137. (in Chinese)
[13]	Ma Yinan, Tao Wang, Chen Yanbin. Laser spot welding of LF6 aluminum with double laser beams[J]. Infrared and Laser Engineering, 2014, 43(3):707-711. (in Chinese)
[14]	Lin R, Wang H P, Lu F, et al. Numerical study of keyhole dynamics and keyhole-induced porosity formation in remote laser welding of Al alloys[J]. International Journal of Heat and Mass Transfer, 2017, 108:244-256.

[1]	王慧鹏, 翟思聪, 杨洁, 董丽虹, 王海斗. 基于激光热成像的铝合金表面裂纹宽度定量检测 . 红外与激光工程, 2023, 52(9): 20220902-1-20220902-10. doi: 10.3788/IRLA20220902
[2]	杨正伟, 陈金树, 田干, 张炜, 陈家威, 肖俊玲. 2195-T8铝锂合金激光填丝双面焊熔池行为与接头力学性能研究 . 红外与激光工程, 2023, 52(2): 20220350-1-20220350-9. doi: 10.3788/IRLA20220350
[3]	张月来, 龙维峰, 姚杞, 林吉, 刘泽辉, 刘博文. 铝合金车体焊接同步激光清洗技术研究 (特邀) . 红外与激光工程, 2023, 52(2): 20220534-1-20220534-8. doi: 10.3788/IRLA20220534
[4]	巴一, 韩善果, 杨永强, 郑世达, 师文庆. 激光摆动路径对钢/铝点焊接头组织与性能的影响 . 红外与激光工程, 2022, 51(8): 20210799-1-20210799-10. doi: 10.3788/IRLA20210799
[5]	张晓腾, 李泽文, 周义青, 沈中华. 在亚音速气流作用下连续激光辐照铝合金的穿孔效应 . 红外与激光工程, 2022, 51(2): 20210883-1-20210883-10. doi: 10.3788/IRLA20210883
[6]	蔡家轩, 万乐, 石世宏, 吴捷, 杨强, 石拓, 程梦颖. 激光熔化沉积AlSi10Mg温度场对显微组织性能的影响 . 红外与激光工程, 2022, 51(5): 20210366-1-20210366-10. doi: 10.3788/IRLA20210366
[7]	王凯, 李多生, 叶寅, 罗军明, 龙思海, 官冀原, 谢非彤, 姜苏航, 王明娣, 吴宁. 航空铝合金表面涂层无损激光清洗研究 . 红外与激光工程, 2022, 51(12): 20210936-1-20210936-9. doi: 10.3788/IRLA20210936
[8]	万乐, 石世宏, 夏志新, 张孝足, 傅戈雁, 张荣伟, 李宽. 激光预热/流体冷却辅助激光金属沉积AlSi10Mg成形 . 红外与激光工程, 2021, 50(7): 20200365-1-20200365-10. doi: 10.3788/IRLA20200365
[9]	翟岩, 姜会林, 梅贵, 江帆. 大口径空间红外相机铍铝合金反射镜组件材料选择与设计 . 红外与激光工程, 2020, 49(6): 20190390-1-20190390-7. doi: 10.3788/IRLA20190390
[10]	徐洋洋, 周建忠, 谭文胜, 孟宪凯, 盛杰, 黄舒, 孙昀杰. 深冷激光喷丸强化2024-T351铝合金的表面力学性能 . 红外与激光工程, 2018, 47(12): 1206002-1206002(8). doi: 10.3788/IRLA201847.1206002
[11]	黄磊, 陈希章, 陈兴, 马宏波, 林涛. 镀锌高强钢激光焊接气孔形成机理 . 红外与激光工程, 2017, 46(S1): 1-6. doi: 10.3788/IRLA201746.S106001
[12]	张天宇, 孔斌, 陈敏孙, 杨军, 江厚满. 陶瓷涂层加固铝合金薄板的抗激光性能测试 . 红外与激光工程, 2017, 46(6): 606002-0606002(6). doi: 10.3788/IRLA201746.0606002
[13]	钦兰云, 庞爽, 杨光, 王超, 王维. 激光沉积修复ZL114A铝合金的显微组织及显微硬度研究 . 红外与激光工程, 2017, 46(5): 506004-0506004(6). doi: 10.3788/IRLA201746.0506004
[14]	李建忠, 黎向锋, 左敦稳, 许瑞华, 陈竹. 模拟研究离焦量对7050铝合金Al/Ti熔覆过程的影响 . 红外与激光工程, 2015, 44(4): 1126-1133.
[15]	赵小侠, 罗文峰, 王红英, 杨森林, 朱海燕, 李姝丽, 付福兴, 李院院. 基于LIBS 技术铝合金中铁元素的定量分析 . 红外与激光工程, 2015, 44(1): 96-101.
[16]	郭卫, 孔德军, 叶存冬, 张垒. 激光热处理对1Cr5Mo耐热钢焊接接头拉伸性能的影响 . 红外与激光工程, 2015, 44(4): 1145-1149.
[17]	于树海, 王建立, 董磊, 刘欣悦. 基于T 型稀疏发射阵列的傅里叶望远镜 . 红外与激光工程, 2014, 43(1): 190-194.
[18]	闫世兴, 董世运, 徐滨士, 王玉江, 任维彬, 方金祥. 激光熔覆过程中熔池对流运动对熔覆层气孔和元素分布的影响 . 红外与激光工程, 2014, 43(9): 2832-2839.
[19]	马轶男, 陶汪, 陈彦宾. LF6铝合金双光束激光点焊工艺研究 . 红外与激光工程, 2014, 43(3): 707-711.
[20]	唐庆菊, 王扬, 刘俊岩, 秦雷, 龚金龙, 齐立涛. 耐热合金涂层结构板材内部缺陷的脉冲红外热成像检测 . 红外与激光工程, 2013, 42(7): 1685-1690.

点击查看大图

计量

文章访问数: 486
HTML全文浏览量: 96
PDF下载量: 29
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

铝合金T型接头双侧激光焊接气孔缺陷影响规律研究

doi: 10.3788/IRLA201847.0906004

作者简介:
杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn

Study on the influence rule of porosity defects for double-sided laser beam welding of aluminum alloy T-joint

计量

铝合金T型接头双侧激光焊接气孔缺陷影响规律研究

doi: 10.3788/IRLA201847.0906004

1. 大连交通大学材料科学与工程学院,辽宁大连 116028

作者简介:
杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn

English Abstract

Study on the influence rule of porosity defects for double-sided laser beam welding of aluminum alloy T-joint

1. School of Materials Science and Engineering,Dalian Jiaotong University,Dalian 116028,China

全文HTML

目录

留言板

铝合金T型接头双侧激光焊接气孔缺陷影响规律研究

doi: 10.3788/IRLA201847.0906004

作者简介: 杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn

Study on the influence rule of porosity defects for double-sided laser beam welding of aluminum alloy T-joint

计量

出版历程

铝合金T型接头双侧激光焊接气孔缺陷影响规律研究

doi: 10.3788/IRLA201847.0906004

1. 大连交通大学 材料科学与工程学院,辽宁 大连 116028

作者简介: 杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn

English Abstract

Study on the influence rule of porosity defects for double-sided laser beam welding of aluminum alloy T-joint

1. School of Materials Science and Engineering,Dalian Jiaotong University,Dalian 116028,China

全文HTML

目录

作者简介:
杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn

1. 大连交通大学材料科学与工程学院,辽宁大连 116028

作者简介:
杨志斌(1985-),男,讲师,博士,主要从事激光焊接及其数值模拟等方面的研究。Email:yangzhibin@djtu.edu.cn