-
激子极化激元是在半导体微腔中在一定条件下出现的一种准粒子。这种准粒子是激子(强耦合作用下的电子-空穴对)与光子的耦合。它的粒子自旋符合玻色-爱因斯坦统计。在量子涡旋陀螺的概念下,激子极化激元被囚禁在一个具有圆周对称性的半导体微腔中。微腔的上下表面为分布式布拉格反射镜(Distributed Bragg Reflector,DBR)。这样,一定波长的泵浦光就可以在微腔内来回振荡,形成平板形法布里-珀罗腔。光子在微腔中来回振荡的传播模式称为腔模。这样可以在微腔中形成激子-光子强耦合,使它们在极化作用下形成“激子极化激元”。当泵浦光超过一定阈值时,这些激子由于其强烈的非线性相互作用,能量会逐渐减低到基态,形成BEC。通过携带OAM的涡旋光对这种凝聚态进行操纵,可以得到量子化的叠加态涡旋,这种量子化的叠加态涡旋可以表征BEC体系在惯性系下显示出的陀螺效应。
如图1所示,考虑陀螺仪的旋转特性,笔者研究了光驱动下圆周对称平面半导体微腔中激子极化激元凝聚的演化过程。激子极化激元场分布可以看做是激子场和光子场相互耦合形成的,具有典型的双分量结构。但是,它同时又是独立的,因此,根据研究对象的不同,研究激子极化激元的激发特性可以从两个方面着手,即双分量模型和单分量模型。
图 1 量子涡旋陀螺半导体微腔中的激子极化激元体系。(a)泵浦光驱动的平板微腔结构;(b)激子极化激元在旋转状态下凝聚的体系;(c)光激发下激子极化激元形成过程[15]
Figure 1. Exciton polariton system in microcavity of quantum vortex gyroscope. (a) Flat microcavity structure driven by pump light; (b) System of exciton polariton condensates on the rotational state; (c) Formation process of exciton polariton under light excitation[15]
这里用色散关系来描述微腔中激子和光子之间的能量耦合。色散关系由下列数学表达式给出:
$$ \begin{split} {H} = &\int {{{\rm{d}}^2}r\sum\limits_{i,j}^{\left\{ {X,C} \right\}} {\hat \psi _i^{\text{ + }}\left( r \right)\left[ {{h_{ij}} + {V_{ij}}\left( r \right){\delta _{ij}}} \right]} } {{\hat \psi }_j}\left( r \right) +\\ & \frac{{\hbar {g_X}}}{2}\int {{{\rm{d}}^2}r} \hat \psi _X^{\text{ + }}\left( r \right)\hat \psi _X^{\text{ + }}\left( r \right){{\hat \psi }_X}\left( r \right){{\hat \psi }_X}\left( r \right) +\\ & \int {{{\rm{d}}^2}r} \hbar {F_P}\left( r \right)\hat \psi _C^{\text{ + }}\left( r \right) + H.c \end{split} $$ (1) 半导体微腔中的激子极化激元场可以用激子场
$ {\overset{\lower0.5 em\hbox{$\smash{\scriptscriptstyle\frown}$}}{\psi } _X}\left( {r,t} \right) $ 与光子场$ {\overset{\lower0.5 em\hbox{$\smash{\scriptscriptstyle\frown}$}}{\psi } _C}\left( {r,t} \right) $ 的耦合来描述。这是一个写在极坐标空间中的双分量模型哈密顿量。$ i,j \in \left\{ {X,C} \right\} $ 表示空间坐标,分别表示激子场和光子场的分量。这些分量满足玻色交换关系,即:$$ \left[ {{{\hat \psi }_i}\left( r \right),\hat \psi _j^\dagger \left( {r'} \right)} \right] = {\delta ^2}\left( {r - r'} \right){\delta _{ij}} $$ (2) 单个粒子的哈密顿量h为:
$$ {{h = }}\hbar \left( {\begin{array}{*{20}{c}} {{\omega _X}}&{{\varOmega _R}} \\ {{\varOmega _R}}&{{\omega _C}} \end{array}} \right) $$ (3) 此时,激子与光子之间的耦合可以用矩阵中的
${\varOmega _R}$ 项来描述,称为拉比分裂。光子场的色散关系由以下公式给出:$$ {\omega _C}\left( k \right) = \omega _C^0 + \frac{{{\hbar ^2}{k^2}}}{{2{m_C}}} $$ (4) 激子极化激元的色散关系由对角化的单粒子哈密顿量h给出,即:
$$ {\omega _{UP/LP}}\left( k \right) = \frac{1}{2}\left\{ {\left[ {\omega _X^0 + {\omega _C}\left( k \right)} \right] \pm \sqrt {{{\left[ {\omega _X^0 - {\omega _C}\left( k \right)} \right]}^2} + 4{\varOmega _R}^2} } \right\} $$ (5) 以上是激子极化激元相位刻印的理论基础和实现原理。其本质在于光子与激子的耦合,而耦合过程就是能量与相位信息传递的过程。
量子涡旋陀螺仪体系的数值模拟,主要研究对象是半导体微腔中受激电子-空穴对的叠加态和演化特征,不包括光子成分。基于此,考虑选择一种单分量模型[10]:
$$ \begin{split} i\hbar \frac{\partial }{{\partial t}}\psi \left( r \right) =& \left[ { - \frac{{{\hbar ^2}}}{{2m}}{\nabla ^2} + {V_{ext}}\left( r \right) + g{{\left| {\psi \left( r \right)} \right|}^2} +}\right.\\ &\left.{\frac{i}{2}\left( {P\left( r \right) - \gamma - \eta {{\left| {\psi \left( r \right)} \right|}^2}} \right)} \right]\psi \left( r \right) \end{split} $$ (6) 这也称为Gross-Pitaevskii (GP)方程。用波函数
$\psi \left( r \right)$ 来描述激子极化激元场,其中${V_{ext}}\left( r \right)$ 为激子场感受到的结构势垒;$P\left( r \right)$ 为泵浦项;$g$ 表示激子极化激元之间的非线性相互作用;$\gamma $ 为系统损耗项;$\eta $ 为激励饱和参数。为了便于计算各系统参数对陀螺效应的影响,建立了GP方程的数值模型,并根据该模型计算和研究了不同初始值和边界条件下激子极化激元的演化过程。数值模型构建方法如图2所示。该GP方程的数值模型由主程序和若干子程序组成。其中主程序为系统各变量赋值并定义初始解,然后在for循环中实现激子极化激元叠加态涡旋随时间演化的过程的计算,得到
$\psi \left( r \right)$ 的概率密度${\left| {\psi \left( r \right)} \right|^2}$ 和相位分布随时间演化的结果。每个子程序都可以被主程序调用。差分方法如图3所示。子程序主要包括系统几何参数的定义、仿真变量的定义、势函数
${V_{ext}}\left( r \right)$ 的定义、四阶Runge-Kutta法差分、时域FDTD、柱坐标下的拉普拉斯算子,以及泵浦光和信号光的数值模型。通过系统变量的定义,将所有变量定义在一个字典中,实现子程序之间的相互调用。数值模型的变量如表1所示,均进行了无量纲处理。为了保证变量具有正确的物理意义,并使计算过程正确,对这些变量的取值范围和取值类型进行了指定,具体规定将在下文体现。通过调整系统差分步长和系统仿真总时间来控制计算精度和迭代速度。通过调整激子极化激元系统特性变量可以研究失谐、非线性相关因子、驰豫与饱和因子等重要系统特性对系统演化过程的影响,并以此进一步求出系统稳定或失稳的边界值。此外,通过调节泵浦光的参数,可以研究不同结构和不同强度的泵浦光对系统稳定性的重要影响。表 1 数值模型的关键参数及参数含义
Table 1. Key parameters of the numerical model and the corresponding parameter meaning
Important parameters Parameter meaning Important parameters Parameter meaning t0 Time step nt Calculate the total time t_order Time difference order IOAM Topological charge number NDIM Radial lattice number NANGLE Angular lattice number r1 Microcavity inner diameter r2 Microcavity outer diameter DR Radial lattice length DA Angular lattice point length Meff Effective mass g Nonlinear interaction γ Inherent loss of system η Saturation compensation term Pw Pump light size Pamplitude Pump light intensity r0 Pump optical center rw Light center nrhalfwave Radial half wavelength number φ0 Initial wave function -
量子涡旋陀螺仪的激子极化激元体系实际上是一个驱动耗散型的动力学系统。由于各种因素的干扰,系统的弱动力学平衡会被打破,从而失去产生陀螺效应的可能性。文中主要从泵浦光和信号光的几何参数和强度分布以及微腔的材料参数两个方面分析了量子涡旋陀螺仪的BEC体系。主要分析了这两个参数对叠加态系统演化过程、实空间分布和相位分布的影响,验证了上述数学模型的可行性。
-
量子涡旋陀螺仪的工作区域是一个嵌入在一个平坦的微腔中圆形对称的量子阱。需要在叠加态涡旋的“花瓣状”条纹区域周围产生环形泵浦,将激子连续泵入热激子库,建立一个“泵浦-弛豫”的过程。因此,环形泵浦光的几何参数已成为影响量子涡旋陀螺仪演化和稳定性的关键因素。这部分主要研究了环的宽度和环直径的影响。
如图4所示,当环形泵浦光的半径沿径向变化时,激子极化激元BEC叠加态涡旋体系的演化过程明显不同。这里时间单位是
$\hbar /{\rm{meV}}$ ,对应于物理时间$6.582\;1 \times {10^{{{ - }}13}}$ s。下文都将用这个时间单位来描述演化时间。根据计算结果可以得出,当泵浦光相对靠近环形微腔内侧时,如图4 (a)所示,量子涡旋陀螺仪系统的演化过程存在明显的周期性波动,演化曲线如图4 (d)所示。类似的情况发生在泵浦光接近环形微腔的外侧,如图4(c)和图4(f)所示。当泵浦光处于环型微腔的中心时,如图4(b)所示,演化的量子涡旋陀螺仪激子极化激元系统是最稳定的,见图4 (e)。此外还发现,当泵浦光处于环型微腔中心时,体系叠加态的演化更快地接近稳定。这可以通过比较图4 (d)、(e)、(f)的纵坐标,借助数学模型发现,当泵浦光的位置在环型微腔的中心时,体系的演化是最好的,此时径向物质波容易发生干涉产生叠加态花瓣,这也有助于叠加态涡旋的稳定演化。图 4 不同泵浦光位置对量子涡旋陀螺仪演化的影响。(a)~(c) 泵浦光与环形量子阱的相对位置,其中环形量子阱是被白色虚线圈包围的部分,内径为5 μm,外径为10 μm;(d)~(f) 量子涡旋陀螺仪体系中激子极化激元随时间的演化规律,演化时间为40
$\hbar /{\rm{meV}}$ Figure 4. Influence of different pump light positions on the evolution of quantum vortex gyroscope. (a)-(c) Relative position of the pump light and the ring quantum well, where the ring quantum well is the part surrounded by a white dashed circle, with the inside diameter of 5 μm and the outer diameter of 10 μm; (d)-(f) Evolution law of exciton polariton in quantum gyro system with time in period of 40
$\hbar /{\rm{meV}}$ -
量子涡旋陀螺仪是一种全光操控的陀螺仪。叠加态涡旋的形成在于泵浦光的能量泵浦和涡旋光轨道角动量传递的双重作用。在研究泵浦光几何尺寸和强度对系统演化特性影响的基础上,有必要研究泵浦光和信号光对叠加态系统的组合效应。
可以明显地发现,泵浦光的强度和宽度对激子极化激元体系的演化和稳定性有影响。图5中右侧标度0代表环形微腔中的激子极化激元BEC体系随时间演化最终在数学计算上会发散,即“不稳定”,1则代表“稳定”。这一稳定性判别方法通过GP方程线性化后求得的通解再代入引入微扰非线性项的方程中求出特解,并将算符对角化,提取特征值,对特征值虚部的符号判断得来。那么从三维图则可以反映泵浦光强度-尺寸对环形微腔中的激子极化激元BEC体系稳定性的联合影响,以及泵浦强度-涡旋光(信号光)强度对激子极化激元BEC体系稳定性的联合影响。从图5 (a)中可以看出,当泵浦光的宽度小于一定范围时,泵浦光的强度对叠加态涡旋的稳定演化有显著的影响。根据计算,在能量密度允许的情况下,泵浦光直径应保持在势阱直径的10倍以上。此时系统将处于非常稳定的状态,泵浦光强的变化对系统的稳定性影响相对较小。此外,研究了泵浦光和信号光(涡旋光)对叠加态涡旋系统的共同影响,如图5 (b)所示。泵浦光和信号光对系统演化和稳定性的影响近似线性。然而,这里的信号光强度远远高于泵浦光。当信号光强度与泵浦光强度之差小于200%时,无法计算出信号光对系统稳定性的影响。
图 5 仅在泵浦光作用下叠加态涡旋的演化稳定性和泵浦光/信号光联合作用下的演化稳定性。(a)仅在泵浦光作用下,泵浦光大小和泵浦光强对系统演化特性的影响;(b)泵浦光和信号光对涡旋叠加状态的联合影响
Figure 5. Evolution stability of the superposition state of the vortex only under the action of the pump light and the evolution stability under the combined action of the pump light/signal light. (a) Influence of pump light size and pump light intensity on the evolution characteristics of the system only under the action of pump light; (b) Joint influence of pump light and signal light on superposition state of vortex
随后,研究了泵浦光与信号光的相对位置对激子极化激元叠加态体系演化的影响,如图6所示。在第一种情况下,当泵浦光(半径为15 μm)完全覆盖半径为10 μm的信号光时,激子极化激元叠加态涡旋相对稳定;叠加态涡旋的干涉花瓣分布区域随时间周期性振荡,如图6 (b)~(d)所示。在第二种情况下,泵浦光的范围(半径为14.8 μm)和信号光(半径15 μm)几乎是相同的,叠加态的激子极化激元涡旋也相对稳定,然而干涉花瓣的振荡区域消失,花瓣会稳定在一个固定的位置。在第三种情况下,泵浦光(半径为7.5 μm)的范围明显小于信号光(半径为10 μm),此时可以发现,激子极化激元叠加态涡旋发生了明显的变化,随着时间的推移,干扰花瓣的区域会显著旋转,干涉花瓣的形状也发生了明显的变化。据此推测:当泵浦光的边缘落在信号光的作用范围内时,它所形成的激子库阻碍了叠加态涡旋在微腔中的传播,这样,激子极化激元叠加态涡旋的相位就会被破坏。
图 6 泵浦光与信号光不同位置关系下量子涡陀螺仪激子极化激元叠加态演化特征。(a)、(e)和(i) 泵浦光与信号灯的不同位置关系(红色区域为泵浦光,蓝色区域为信号灯);(b)~(d) 轨道角动量±1@
$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ 和$60\;\hbar /{\rm{meV}}$ 的涡叠加态;(f)~(h) 轨道角动量±1@$20\;\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ 和$60\;\hbar /{\rm{meV}}$ 的涡叠加态;(j)~(l)轨道角动量±1@$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ 的叠加态涡旋Figure 6. Evolution characteristics of the superposition state of the exciton polarization exciton of the quantum vortex gyroscope under the different positional relationship between the pump light and the signal light. (a), (e) and (i) Different positional relationship between pump light and signal light (the red area is pump light, and the blue area is signal light); (b)-(d) Vortex superposition state with orbital angular momentum ±1@
$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ ; (f)-(h) Vortex superposition state with orbital angular momentum ±1@$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ ; (j)-(l) Vortex superposition state with orbital angular momentum ±1@$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ -
文中用来捕获激子的量子阱是基于宽禁带半导体材料,如GaAs、GaN、ZnO、卤化物钙钛矿等。在不同的量子阱材料中,激子极化激元的有效质量因材料的各向异性而不同,也间接影响激子极化激元体系与腔光子之间的耦合,可以从色散关系推导出来。此外,微腔材料在不同的生长和涂层过程中表现出不同的均匀性,也导致了材料的无序。这种无序会明显干扰量子涡旋陀螺仪的实际应用效果,因为在不同的干涉区域可能存在不同的耦合强度,将极大地破坏量子涡旋陀螺仪的稳定相位分布。因此,从表征材料自然特性的有效质量和表征材料工程特性的无序噪声两个方面研究这些参数对量子涡旋陀螺仪涡旋叠加系体系演化过程的影响。
首先,考虑不同材料的各向异性引起激子极化激元有效质量的差异。微腔有效质量的差异与激子极化激元和腔光子在微腔中的耦合和能量传递直接相关。这也对应于微腔失谐参数,该参数是表征微腔材料性能的重要参数。在数值计算中,“mass”(有效质量)被用来表征失谐。这一定义的理论基础是激子极化激元的色散关系:
$$ \omega = \frac{1}{2}\left[ {{E_C}\left( k \right) + {E_X}\left( k \right) - \sqrt {{{\left( {{E_C}\left( k \right) - {E_X}\left( k \right)} \right)}^2} + 4{\varOmega ^2}} } \right] $$ (7) 对其进行泰勒展开,可得到近似解:
$$ \omega {{ = }}{E_{C0}} + {E_{X0}} + \alpha {k^2} + \beta {k^2} - \sqrt {{{\left( {{E^2}_{C0} - {E^2}_{X0} + \alpha {k^2} - \beta {k^2}} \right)}^2} + 4{\varOmega ^2}} $$ (8) 忽略无穷小量,简化如下:
$$ \omega {\text{ = }}{E_0} + A{k^2} $$ (9) 其中,系数A可以反映系统的失谐,且
$A \propto \dfrac{\hbar }{{2 m}}$ 。这样,微腔的失谐可以用有效质量“mass”来表征。为了使其具有实际的物理意义,在计算过程中取mass∈(0.1, 10)。当有效质量处于使系统不稳定的临界值时激子极化激元叠加态的实空间分布及演化特性曲线如图7所示。通过数值模型计算出有效质量的临界值为0.523,图7 (a)、(c)为叠加态涡旋OAM=±3的实空间分布和演化过程的曲线。当质量减少到0.523时会出现一个现象:经过演化后,由于激子极化激元向中心势垒边缘移动,原本分布在花瓣位置的叠加态涡旋明显减弱。相反,在中心势垒的边缘出现了激子极化激元密集分布的现象。同时,与有效质量为1时相比,局域粒子数量显著增加,这意味着系统中激发的激子更多。当有效质量进一步降低到0.48时,系统中的激子被急剧激发。相对于质量的临界值0.523,局域粒子数在演化过程中的极值为1728.23,该值急剧增加到102438.9,演化曲线急剧振荡,系统已经失稳,如图7 (d)所示。此时,叠加态涡旋消失,所有激子都分布在中心势垒边缘的一个很窄的范围内,如图7 (b)所示。
图 7 有效质量达到使系统不稳定的临界值时激子极化激元叠加态的实空间分布及演化特性曲线
Figure 7. Real-space distribution and evolution characteristic curve of the superposition state of the exciton polarization exciton when the effective mass isat the critical value that makes the system unstable
通过对衡量系统失谐参数的变量mass的计算和分析,可以得知,失谐参数大于临界值(mass小于临界值0.523)时,系统会失稳,无法形成稳定的叠加态涡旋。当失谐参数小于临界值(mass大于临界值2.19)时,虽然系统依然存在花瓣解的叠加态涡旋,但这种叠加态涡旋的相位分布并不稳定,不是最优解。通过对一组不同mass取值的局域粒子数演化曲线的对比可以发现,当mass变量过大或过小时,系统都会失稳,处于激子极化激元数量反复增加-耗散的震荡过程。如图8所示,可以发现存在一个系统稳定区间,此时mass∈(0.7, 10)。
Simulation analysis of some key parameters of quantum vortex gyroscope (Invited)
-
摘要: 半导体微腔中由光驱动的激子极化激元体系是近年来热门的物理学、光学领域研究方向,而半导体微腔中由光驱动的玻色-爱因斯坦凝聚体(Bose-Einstein Condensates, BEC)的量子叠加态涡旋在量子传感领域具有颠覆性的潜在应用价值。通过Runge-Kutta差分和FDTD有限元方法构建了一个精确的数学模型来表征量子涡旋陀螺激子极化激元体系的时空演化规律。在此基础上,研究了泵浦光、信号光和与半导体微腔材料相关的一些关键参数对量子涡旋陀螺激子极化激元凝聚体演化特性的影响。其中泵浦光和信号光考虑了环形光斑的几何尺寸以及它们的光强,而微腔材料对激子极化激元体系的影响通过数学上的变换,折算为有效质量对BEC体系的影响。通过大量参数扫描,得到了影响量子涡旋陀螺性能的一些关键因素,包括泵浦光的几何参数和强度、泵浦光和信号光的相关影响以及半导体微腔的材料特性。通过表征不同微腔材料的有效质量与性能之间的关系,计算了材料性能与量子涡旋陀螺仪叠加态演化之间的关系,发现有效质量的合理值范围很窄。这些工作为量子涡旋陀螺的工程样机研发提供了重要参考。Abstract: The exciton polaritons in the semiconductor microcavity driven by light is a hot research field in physics and optics in recent years, and the superposition quantized vortex of the Bose-Einstein Condensates (BEC) driven by light in the microcavity has subversive potential application value in the field of quantum sensing. An accurate mathematical model via Runge-Kutta Difference and FDTD finite element method was constructed to characterize the time-space evolution of the quantum vortex gyrotron polariton system. On this basis, the influence of some key parameters related to pump light, signal light and semiconductor microcavity materials on the evolution characteristics of the quantum vortex gyroscope exciton polariton condensate was studied. For the pump light and signal light, the light intensity and geometric size of the annular spot were considered. Meanwhile, the effect of the microcavity material on the exciton polariton system was converted into the effect of the effective mass on the BEC system through mathematical transformation. By scanning a lot of parameters, some key factors affecting the performance of the quantum vortex gyroscope were obtained, including the geometric parameters and intensity of the pump light, the related influence of the pump light and the signal light, and the material properties of the semiconductor microcavity. The relationship between material properties and superposition state evolution of quantum vortex gyroscope was calculated by characterizing the relationship between effective mass and properties of different microcavity materials, and the range of reasonable values for effective mass was found to be narrow. These works provided an important reference for the engineering prototype development of the quantum vortex gyroscope.
-
图 1 量子涡旋陀螺半导体微腔中的激子极化激元体系。(a)泵浦光驱动的平板微腔结构;(b)激子极化激元在旋转状态下凝聚的体系;(c)光激发下激子极化激元形成过程[15]
Figure 1. Exciton polariton system in microcavity of quantum vortex gyroscope. (a) Flat microcavity structure driven by pump light; (b) System of exciton polariton condensates on the rotational state; (c) Formation process of exciton polariton under light excitation[15]
图 4 不同泵浦光位置对量子涡旋陀螺仪演化的影响。(a)~(c) 泵浦光与环形量子阱的相对位置,其中环形量子阱是被白色虚线圈包围的部分,内径为5 μm,外径为10 μm;(d)~(f) 量子涡旋陀螺仪体系中激子极化激元随时间的演化规律,演化时间为40
$\hbar /{\rm{meV}}$ Figure 4. Influence of different pump light positions on the evolution of quantum vortex gyroscope. (a)-(c) Relative position of the pump light and the ring quantum well, where the ring quantum well is the part surrounded by a white dashed circle, with the inside diameter of 5 μm and the outer diameter of 10 μm; (d)-(f) Evolution law of exciton polariton in quantum gyro system with time in period of 40
$\hbar /{\rm{meV}}$ 图 5 仅在泵浦光作用下叠加态涡旋的演化稳定性和泵浦光/信号光联合作用下的演化稳定性。(a)仅在泵浦光作用下,泵浦光大小和泵浦光强对系统演化特性的影响;(b)泵浦光和信号光对涡旋叠加状态的联合影响
Figure 5. Evolution stability of the superposition state of the vortex only under the action of the pump light and the evolution stability under the combined action of the pump light/signal light. (a) Influence of pump light size and pump light intensity on the evolution characteristics of the system only under the action of pump light; (b) Joint influence of pump light and signal light on superposition state of vortex
图 6 泵浦光与信号光不同位置关系下量子涡陀螺仪激子极化激元叠加态演化特征。(a)、(e)和(i) 泵浦光与信号灯的不同位置关系(红色区域为泵浦光,蓝色区域为信号灯);(b)~(d) 轨道角动量±1@
$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ 和$60\;\hbar /{\rm{meV}}$ 的涡叠加态;(f)~(h) 轨道角动量±1@$20\;\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ 和$60\;\hbar /{\rm{meV}}$ 的涡叠加态;(j)~(l)轨道角动量±1@$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ 的叠加态涡旋Figure 6. Evolution characteristics of the superposition state of the exciton polarization exciton of the quantum vortex gyroscope under the different positional relationship between the pump light and the signal light. (a), (e) and (i) Different positional relationship between pump light and signal light (the red area is pump light, and the blue area is signal light); (b)-(d) Vortex superposition state with orbital angular momentum ±1@
$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ ; (f)-(h) Vortex superposition state with orbital angular momentum ±1@$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ ; (j)-(l) Vortex superposition state with orbital angular momentum ±1@$20\;\hbar /{\rm{meV}}$ ,$40\;\hbar /{\rm{meV}}$ and$60\;\hbar /{\rm{meV}}$ 表 1 数值模型的关键参数及参数含义
Table 1. Key parameters of the numerical model and the corresponding parameter meaning
Important parameters Parameter meaning Important parameters Parameter meaning t0 Time step nt Calculate the total time t_order Time difference order IOAM Topological charge number NDIM Radial lattice number NANGLE Angular lattice number r1 Microcavity inner diameter r2 Microcavity outer diameter DR Radial lattice length DA Angular lattice point length Meff Effective mass g Nonlinear interaction γ Inherent loss of system η Saturation compensation term Pw Pump light size Pamplitude Pump light intensity r0 Pump optical center rw Light center nrhalfwave Radial half wavelength number φ0 Initial wave function -
[1] Popov E, Barantsev K, Litvinov A. Theoretical simulation of a signal for the scheme of an atomic spin gyro with optical detection [J]. Quantum Electronics, 2019, 49: 169-177. [2] Barrett B, Cheiney P, Battelier B, et al. Multidimensional atom optics and interferometry [J]. Physical Review Letters, 2019, 122: 043604. [3] Porras D, Ciuti C, Baumberg J J, et al. Polariton dynamics and Bose-Einstein condensation in semiconductor microcavities [J]. Physical Review B, 2002, 66: 085304. [4] Saba M, Ciuti C, Kundermann S, et al. Polariton parametric amplification in semiconductor microcavities [J]. Journal of Modern Optics, 2002, 49: 2437-2458. [5] Hartmann M J. Quantum simulation with interacting photons [J]. Journal of Optics, 2016, 18: 104005. [6] Lenef A, Hammond T D, Smith E T, et al. Rotation sensing with an atom interferometer [J]. Physical Review Letters, 1997, 78: 760-763. [7] Rahimi-Iman A. Towards Polariton Condensates and Devices [M]. Berlin: Springer International Publishing, 2020. [8] Wang Chen, Ren Yuan, Wu Hao, et al. Generation of optical vortex and its research progress in inertial measurement (Invited) [J]. Infrared and Laser Engineering, 2021, 50(9): 20200463. (in Chinese) doi: 10.3788/IRLA20200463 [9] Ding You, Ding Yuansheng, Qiu Song, et al. Rotational frequency detection of spinning objects at general incidence using vortex beam (Invited) [J]. Infrared and Laser Engineering, 2021, 50(9): 20210451. (in Chinese) doi: 10.3788/IRLA20210451 [10] Hodby E, Hopkins S A, Hechenblaikner G, et al. Experimental observation of a superfluid gyroscope in a dilute Bose-Einstein condensate [J]. Physical Review Letters, 2003, 91: 090403. [11] Thanvanthri S, Kapale K T, Dowling J P. Ultra-stable matter-wave gyroscopy with counter-rotating vortex superpositions in Bose-Einstein condensates [J]. Journal of Modern Optics, 2012, 59: 1180-1185. [12] Moxley F I, Dowling J P, Dai W, et al. Sagnac interferometry with coherent vortex superposition states in exciton-polariton condensates [J]. Physical Review A, 2016, 93: 053603. [13] Cristofolini P, Dreismann A, Christmann G, et al. Optical superfluid phase transitions and trapping of polariton condensates [J]. Physical Review Letters, 2013, 110: 186403. [14] Han Q, Wang J, Lu J, et al. Transition between exciton-polariton and coherent photonic lasing in all-inorganic perovskite microcuboid [J]. ACS Photonics, 2020, 7: 454-462. [15] Chestnov I Y, Kavokin A V, Yulin A V. The optical control of phase locking of polariton condensates [J]. New Journal of Physics, 2019, 21: 113009. [16] Ren J, Liao Q, Huang H, et al. Efficient bosonic condensation of exciton polaritons in an h-aggregate organic single-crystal microcavity [J]. Nano Letters, 2020, 20: 7550-7557. [17] Wu H, Ren Y, Liu T, et al. Rotational dynamics characteristics of planar superimposed vortices of exciton polariton condensates [J]. Acta Physica Sinica, 2020, 69(23): 230303.