Volume 46 Issue 5
Jun.  2017
Turn off MathJax
Article Contents
Article Navigation >  Infrared and Laser Engineering  > 2017  >  46(5): 506004-0506004(6)

Qin Lanyun, Pang Shuang, Yang Guang, Wang Chao, Wang Wei. Microstructure and micro-hardness of laser deposition repair ZL114A aluminum alloy[J]. Infrared and Laser Engineering, 2017, 46(5): 506004-0506004(6). doi: 10.3788/IRLA201746.0506004
Citation: Qin Lanyun, Pang Shuang, Yang Guang, Wang Chao, Wang Wei. Microstructure and micro-hardness of laser deposition repair ZL114A aluminum alloy[J]. Infrared and Laser Engineering, 2017, 46(5): 506004-0506004(6). doi: 10.3788/IRLA201746.0506004
shu

Microstructure and micro-hardness of laser deposition repair ZL114A aluminum alloy

doi: 10.3788/IRLA201746.0506004
  • 1.

    Key Laboratory of Fundamental Science for National Defence of Aeronautical Digital Manufacturing Process,Shenyang Aerospace University,Shenyang 110136,China

  • Received Date: 2016-09-06
  • Rev Recd Date: 2016-10-10
  • Publish Date: 2017-05-25
  • To study the process and properties of laser deposition repair (LDR) ZL114A aluminum alloy samples, the basic process experiment of multi parameter combination was accomplished by laser single-pass process, on the basis of analyzing surface features, the reasons of gas porosity, a set of optimized process parameters were obtained, and defect-free block specimens were prepared, microstructure analysis and hardness testing of the samples were carried out. Results show that the repair area and the substrate form a good metallurgical combination. -Al columnar dendrites took melt pool edge as a starting point at the bottom of the deposition layer. The primary dendrites arm spacing was 18.38 m and the distance between dendrite crystal was 9.55 m. On the top of the deposited layers, -Al dendrite columnar crystal was changed into equiaxed dendrite microstructure. Si phase was precipitated and tended to be spheroidize in the layer band of the repaired zone. Due to the function of grain refinement and solution strengthening, the micro-hardness of the deposited area was 25.8% higher than that of the substrate.
  • [1] Ma Siqun, Gu Lixiang, Yuan Yongwen, et al. Research on influence of welding defects on fatigue life of EMU aluminum-alloy car body[J]. Journal of the China Railway Society, 2014, 36(2):42-48. (in Chinese)马思群, 谷理想, 袁永文, 等. 焊接缺陷对动车组铝合金车体疲劳寿命影响研究[J]. 铁道学报, 2014, 36(2):42-48.
    [2] Casalino G, Mortello M, Paola Leo, et al. Study on arc and laser powers in the hybrid welding of AA574 Al-alloy[J]. Materials and Design, 2014, 61:191-198.
    [3] Lin Xin, Huang Weidong. High-performance laser gain material of metal components manufacturing[J]. Scientia Sinica Informationis, 2015, 45(9):1111-1126. (in Chinese)林鑫,黄卫东. 高性能金属构件的激光增材制造[J]. 中国科学:信息学, 2015, 45(9):1111-1126.
    [4] Wang Huaming. Materials fundamental issues of laser additive manufacturing for high-performance large metallic components[J]. Acta Aeronautic et Astronautica Sinica, 2014, 35(10):2690-2698. (in Chinese)王华明. 高性能大型金属构件激光增材制造:若干材料基础问题[J]. 航空学报, 2014, 35(10):2690-2698.
    [5] Watkins K G, McMahon M A, Streen W M. Microstructure and corrosion properties of laser surface processed aluminium alloys:a review[J]. Materials Science and Engineering A, 1997, 231(1-2):55-61.
    [6] Zhuang W, Liu Q, Djugum R, et al. Deep surface rolling for fatigue life enhancement of laser clad aircraft aluminium alloy[J]. Applied Surface Science, 2014, 320:558-562.
    [7] Ehsan Toyserkani, Stephen Corbin, Amir Khajepour. Laser Cladding[M]. New York:CRC Press, 2005.
    [8] Wang Xiaoyan, Chen Jing, Lin Xin, et al. Microstructure of laser forming repair 7050 aluminum alloy with AlSi12 powder[J]. Chinese of Journal of Lasers, 2009, 36(6):1585-1590. (in Chinese)王小艳, 陈静, 林鑫, 等. AlSi12粉激光成形修复7050铝合金组织[J]. 中国激光, 2009, 36(6):1585-1590.
    [9] Xue Lei, Huang Yixiong, Lu Penghui, et al. Study on microstructure and property of laser forming repaired ZL104 alloy[J]. China Surface Engineering, 2010, 23(1):97-100. (in Chinese)薛蕾, 黄一雄, 卢鹏辉, 等. 激光成形修复ZL104合金的组织与性能研究[J]. 中国表面工程, 2010, 23(1):97-100.
    [10] Zuo Tiechuan. Laser Material Processing of High Strength Aluminum Alloy[M]. Beijing:National Defence Industry Press, 2002:2-10. (in Chinese)左铁钏. 高强铝合金的激光加工[M]. 北京:国防工业出版社, 2002:2-10.
    [11] Chen Xiaoming, Song Renguo, Zhang Yu, et al. Effects of overfire on microstructure and properties of 7003 aluminum alloy[J]. Light Alloy Fabrication Technology, 2009, 37(2):48-52. (in Chinese)陈小明, 宋仁国, 张宇, 等. 过烧对7003铝合金组织与性能的影响[J]. 轻合金加工技术, 2009, 37(2):48-52.
    [12] Zhou Wansheng, Yao Junshan. The Welding of Aluminium and Aluminium Alloy[M]. Beijing:China Machine Press, 2007:40-46. (in Chinese)周万盛, 姚军山. 铝及铝合金的焊接[M]. 北京:机械工业出版社, 2007:40-46.
    [13] Huang Weidong. Laser Solid Forming[M]. Xi' an:Northwestern Polytechnical University Press, 2007:57-60. (in Chinese)黄卫东. 激光立体成形[M]. 西安:西北工业大学出版社, 2007:57-60.
    [14] Shi Lei, Wang Youqi, Wang Ying, et al. Effect of solution treatment on microstructure and mechanical properties of quasi eutectivc Al-Si Alloy[J]. The Chinese Journal of Nonferrous Metals, 2012, 22(12):3372-3377. (in Chinese)石磊, 王有祁, 王英, 等. 固溶处理对准共晶Al-Si合金显微组织及力学性能影响[J]. 中国有色金属学报, 2012, 22(12):3372-3377.
    [15] Chen Yongcheng, Zhang Shuquan, Tian Xiangjun, et al. Microstructure and microhardness of 4045 aluminium alloy fabricated by laser melting deposition.[J]. Chinese of Journal of Lasers, 2015, 42(3):0303008. (in Chinese)陈永城, 张述泉, 田象军, 等. 激光熔化沉积4045铝合金显微组织及显微硬度[J]. 中国激光, 2015, 42(3):0303008.
    [16] Wang Aiqin, Xie Jingpei, Liu Zhongxia, et al. Microstructure and phase structure of rapidly solidified Al-Si alloy[J]. Transactions of Materials and Heat Treatment, 2008, 29(2):99-102. (in Chinese)王爱琴, 谢敬佩, 刘忠侠, 等. 快速凝固Al-Si合金的组织形态及相结构[J]. 材料热处理学报, 2008, 29(2):99-102.
  • 加载中
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索
Get Citation
PDF
XML

Article Metrics

Article views(389) PDF downloads(100) Cited by()

Related
Proportional views

Microstructure and micro-hardness of laser deposition repair ZL114A aluminum alloy

doi: 10.3788/IRLA201746.0506004
  • 1. Key Laboratory of Fundamental Science for National Defence of Aeronautical Digital Manufacturing Process,Shenyang Aerospace University,Shenyang 110136,China
  • Received Date: 2016-09-06
  • Rev Recd Date: 2016-10-10
  • Publish Date: 2017-05-25

Abstract: To study the process and properties of laser deposition repair (LDR) ZL114A aluminum alloy samples, the basic process experiment of multi parameter combination was accomplished by laser single-pass process, on the basis of analyzing surface features, the reasons of gas porosity, a set of optimized process parameters were obtained, and defect-free block specimens were prepared, microstructure analysis and hardness testing of the samples were carried out. Results show that the repair area and the substrate form a good metallurgical combination. -Al columnar dendrites took melt pool edge as a starting point at the bottom of the deposition layer. The primary dendrites arm spacing was 18.38 m and the distance between dendrite crystal was 9.55 m. On the top of the deposited layers, -Al dendrite columnar crystal was changed into equiaxed dendrite microstructure. Si phase was precipitated and tended to be spheroidize in the layer band of the repaired zone. Due to the function of grain refinement and solution strengthening, the micro-hardness of the deposited area was 25.8% higher than that of the substrate.

    HTML

Reference (16)

Catalog

    版权所有 © 2019 《红外与激光工程》编辑部｜ Address: 58 Zhonghuan West Road, Tianjin Airport Economic Zone｜ Post Code: 300308

    津ICP备19007885号-1

    Supported by: Beijing Renhe Information Technology Co. Ltd  

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return